Process design & scale-up / INTERACTIVE LESSON 32

Three projects that force you to think like an engineer

Skip the next certificate. Build a cooling experiment, a mixing calculator and a reproduced worked example you can actually finish.

CHANGE A CONDITION. SEE WHAT FOLLOWS.

Teaching model
Two streams of water mixing into one outletTwo streams in. One temperature out.Idealized: same fluid, steady flow, no heat loss, complete mixingHot in: 1.0 kg/s at 70.0 °CCold in: 1.0 kg/s at 30.0 °CMixed out2.0 kg/s at 50.0 °CHot stream gives up 83.6 kWCold stream gains 83.6 kW

Enlarge for bigger labels, then swipe sideways →

Mixed temperature50.0 °C
Total flow2.0 kg/s
Hot stream gives up83.6 kW
Cold stream gains83.6 kW

1.0 kg/s at 70.0 °C meets 1.0 kg/s at 30.0 °C and leaves at 50.0 °C. That flow-weighted average relies on both streams being the same fluid with equal heat capacity, and on complete mixing. The hot stream gives up 83.6 kW and the cold stream gains the same 83.6 kW, which relies on steady flow and no heat loss.

What this model assumes

Idealized steady-state energy balance for two streams of the same liquid mixing into one: Tmix = (m_hot × T_hot + m_cold × T_cold) / (m_hot + m_cold). Assumptions: both streams are liquid water with the same constant heat capacity (cp = 4.18 kJ/(kg·K)), steady flows, no heat loss to the surroundings, complete mixing and no phase change. The energy rates are m × cp × (temperature change) measured against the mixed temperature, so the hot stream's loss equals the cold stream's gain by construction. Pipe widths in the drawing scale with flow rate; they are not sized pipes. Real mixers have heat loss, imperfect mixing and properties that change with temperature.

THE IDEA TO TAKE WITH YOU

You need a small project you can finish.

You're probably a nerdy engineer. Good. Here are three things you can build instead of collecting another certificate.

One: measure how your coffee cools. Record the temperature over time and fit a simple model. Then compare it with how it cools with a lid on. Your prediction should meet an actual measurement.

Two: make a tiny mixing calculator. Two water streams, known flow rates and temperatures. Predict the mixed temperature under a no-heat-loss assumption. Then change one input and explain why the answer moves.

Three: take a published engineering example and reproduce it from scratch. Track units, assumptions and every place your result disagrees.

What makes this more than another homework exercise: deliberately change something the original example didn't test. Find where your model stops being useful.

You can't become a track athlete by studying track athletes. At some point you have to run. You don't need to quit your job. You need a small project you can finish.

QUICK CHECK

Which changed assumption makes the simple mixing formula unreliable?

THREE PROJECTS YOU CAN FINISH

Pick one. Start this week.

Each card is a small, finishable build. None of them needs special equipment, and the mixing calculator is already running at the top of this page.

Project 01

Measure how your coffee cools

Record the temperature of a cooling drink at regular intervals and note the room temperature. Fit a simple model, such as Newton's law of cooling, to that run. Then repeat with a lid on and see whether your fitted model predicts the second run.

Download the blank observation table (CSV) ↓

Header row only: time_min, temperature_C, lid, room_temperature_C, notes. Nothing is prefilled. Your prediction should meet your own measurement.

Stay at ordinary household drink temperatures and keep hot liquids away from skin and electronics. If you would rather not measure, simulating the experiment with the model alone is enough.

Project 02

Build a tiny mixing calculator

Two water streams with known flow rates and temperatures. Predict the mixed temperature with no heat loss:

Tmix = (mhot × Thot + mcold × Tcold) / (mhot + mcold)

Write it in a spreadsheet or a few lines of code, then check it against the sliders above. The narrated case, 1 kg/s at 70 °C with 1 kg/s at 30 °C, should give 50.0 °C. Doubling the hot flow should give 56.7 °C.

Then change one input and explain, in one sentence, why the answer moved the way it did.

Project 03

Reproduce a published example

Take a worked example from a textbook or an open course and rebuild it from scratch. Track units, assumptions and every place your result disagrees. Then change something the original never tested and find where the model stops being useful.

Assumptions behind the mixing formula. Tick each one you have actually checked.

FROM UNDERSTANDING TO BUILDING

Taking a real process
beyond the lab?

Jon and I are building RARE Labs toward an autonomous pilot plant builder using AI and robotics. Join the waitlist for updates, and tell us what you’re trying to scale.

Join the RARE Labs waitlist ↗

FOLLOW THE EVIDENCE

Go a little deeper.